Lindelacr metalwork is a leading manufacturer of metal ceiling and facade systems.

How Do You Specify Wood-Grain Great Wall Panels for a Tall Lobby?

Specify a wood-grain metal great wall panel on a tall lobby by locking one continuous-grain lot, scanning the as-built plane, then shop-forming the rib and the wave so the wall reads as one surface. LINDELACR did that on the ground-floor lobby of Guangzhou Heji Building (Trendy International Centre). Thickness, alloy, and coating class stay on the shop drawing. This catalog does not print a great-wall gauge. Send the elevation.

Wood-grain aluminum great wall panel wave wall in Guangzhou Heji Building ground-floor lobby, floor-to-ceiling ribs with cove lighting
Heji Building lobby. The wave is a shop-formed great-wall rib, not a timber board. Continuous grain lot. Height is extra-tall; the millimetre is on the scan, not in this caption.

What the building is

Heji Building — also published as Trendy International Centre (TIC) — is the Guangzhou headquarters of Trendy Group in Pazhou, Haizhu. Public listings put gross floor area at about 168,000 m², height at about 192 m, 41 storeys above ground and three below. Architecture is attributed to gmp (Stephan Schütz / Stephan Rewolle). Interiors and landscape are attributed to DH Liberty. Floors 1–6 are published as lobby and commercial; 7–40 as offices. Those figures are from public project notes, not from LINDELACR’s shop file. LINDELACR’s ticket on this job is the ground-floor lobby metal wall: scheme, drawing development, scan, and install guidance.

Guangzhou Heji Building glass tower exterior, vertical curtain-wall bays looking up against an overcast sky
The tower from the street. LINDELACR’s metal is the lobby wall inside, not this glass curtain wall.

What the photographs show

The field is a deep linear aluminum rib — the catalog name is great wall / watchband — with a light oak wood-grain transfer. Some bays run straight and vertical. Some bays are formed into a long horizontal wave. Cove light sits in the head. A brass-coloured skirting and door frame pick up the rib. Fire alarm, hydrant, and sockets sit in cut-outs in the ribs, not as boxes stuck on the face. Marble floor and white soffit are the adjacent trades. One bay still carries green protection mesh: install in progress, not a finished photograph.

Heji Building lobby corridor with wood-grain aluminum great wall panels on both sides, wave wall at right, fluted column wrap at left, marble floor
Both walls are the same grain lot. Left: straight ribs wrapping a core. Right: the wave field. The timber-look soffit in the distance is a separate plane — do not copy this lot onto that board without a drawing.

Why a great-wall rib, not a timber plank

A lobby this tall wants one grain direction, one hue, and a profile that can turn a door, a hydrant, and a wave without site-staining. Indoor wood-grain at LINDELACR is a transfer or print on aluminum, then powder to AAMA 2604 under cover — the same split as the wood-grain ceiling finish note. Exterior sun and rain would step to PVDF AAMA 2605. This lobby is interior. Do not write AAMA 2605 onto a closed hall because the renderer looks “premium.”

WPC and MDF fluted boards show up in Gulf residential searches. A commercial lobby with extra-tall runs, fire services in the rib, and a formed wave is a metal nest: CNC, brake, then one coating lot. The wood-grain surface finish is that face. Profile geometry is the great wall panel page. A freeform wave that must stay a true curve also belongs on the shop drawing the same way a sky-curved panel takes its radius from CAD, not from a site heat-gun.

Mill-finish aluminum wall cassettes stacked in the Foshan shop, formed returns and side hinges before wood-grain coating
Shop stock, mill finish. Fold the return, then run the grain lot. This frame is bare metal, not the oak lobby face.
Close view of undulating wood-grain aluminum great wall ribs with warm cove light in Heji Building lobby
Visible fact: the rib pitch is constant; the wave is in the plane. Inference: extra-tall modules were shop-cut from the scan so vertical joints do not walk.

Scan, drawing, then the wall

LINDELACR’s scope on this lobby was the design scheme, drawing improvement, site scan and measure, and installation guidance. Extra-tall modules are why the scan comes first. A bowed slab or a door that is not plumb will read as a broken grain before it reads as a millimetre. Lock the rib pitch, the grain direction, and the wave stations on the shop drawing. Cut hydrant, bell, and socket pockets in the nest — panel 4 shows those pockets during protection, not as afterthought boxes.

Install crew on a ladder at a Guangzhou Heji Building ground-floor glass line during fit-out, ducts still open, green mesh on the facade
Ground-floor fit-out. Crew at the glass line while ducts are still in the open. This is site coordination, not a photograph of the finished wood-grain rib.

Continuous grain (“连纹”) is a lot decision: one transfer run, grain aligned across modules, so the eye does not pick a panel joint as a timber splice. The photographs show tight rib lines and matched hue. They do not show a wall with zero joints. Doors keep a metal reveal. Protection mesh is still on one bay. Write “visually continuous grain,” not “seamless building.”

Wood-grain aluminum great wall panels wrapping a lobby door with brass frame and recessed fire alarm in Heji Building
The door is a designed reveal. Fire device sits in the rib. That cut is in the unfold.
Wood-grain great wall panel install in Heji lobby with recessed fire hydrant, alarm, and green protection mesh still on
Install in progress. Hydrant and call point in the rib field. Green mesh is protection, not a finish.
Close-up of continuous oak wood-grain transfer on aluminum great wall panel ribs, Heji Building lobby
The grain is a shop face on aluminum. Approve a chip; run one lot for the sightline.

What belongs on the drawing before coil is cut

Item This lobby (verified) Stays on the shop drawing
System Metal great wall / watchband rib, wall cladding Carrier, return, and fixings
Finish Light oak wood-grain transfer, one lot Chip, gloss, grain direction
Geometry Straight ribs and a formed wave Stations from the scan
Height Extra-tall lobby runs (photographs) Module length in mm — pending shop file
Thickness / alloy Not printed on the great-wall catalog table Pending; do not copy 0.6–0.8 mm ceiling sheet onto this rib
Coating class Interior wood-grain; AAMA 2604 is the indoor powder language on other LINDELACR interior tickets Confirm this lot’s data sheet
Openings Hydrant, bell, sockets, doors in the rib Coordinates from scan
Fire / Civil Defence class Not claimed here EN 13501 / local code — pending test report

Gulf tenders that ask for DCD / SCD, EN 13501-1 Class A1/A2, or BS 8414 get those numbers only when the report exists. This article does not attach a Heji fire certificate. Do not copy another plant’s A2 line onto this wall.

Frequently asked questions

Is a wood-grain great wall panel real timber?

No. It is aluminum with a transferred or printed grain. It reads as oak at lobby distance when the lot, gloss, and grain direction are locked. It is still metal.

Can the same rib run straight and as a wave?

Yes if both leave one nest and one coating lot. The Heji lobby does that: straight wraps at cores, a long wave on the feature wall. The curve is on the shop drawing.

How do you hide joints on a tall wood-grain wall?

You do not delete joints. You align grain, keep rib pitch, shop-cut extra-tall modules from a scan, and put services in the unfold. Doors stay a reveal.

Should a UAE or KSA lobby copy this as WPC fluted board?

Not for extra-tall commercial runs with formed waves and fire devices in the rib. WPC is a different ticket. Specify aluminum great wall, one grain lot, and the local fire class on the data sheet.

Send the scan and the chip

Mark the tall bays, the wave, and the services in the rib. LINDELACR will return a shop drawing, a wood-grain chip from the same lot logic as this lobby, and an install sequence. Contact is the form. WhatsApp is the short path for the file.

WhatsApp: send elevation / CAD / BIM / BOQ

Submit CAD/BOQ for factory quotation and 1:1 detailing

Request a wood-grain great-wall profile sample (coated chip). A “3.0 mm free sample box, express to GCC” is only used when that kit is confirmed. Unconfirmed: request the coated sample and mark shipping as a quote line.


Email
Email: lindelacr@lindelacr.com
WhatsApp
(0/8)